The new ride height gauge makes it easier to read Ride Height Readings on chassis and motor mounts particularly when they are chamfered like on the RX28.
Option Steel Lower Pod Plate adds approximately 2.7g of weight to the rear pod of your car. The effect is a little more stability on power. Great for lower bite and faster classes.
This titanium shaft is far tougher than the stock aluminum diff all while maintaining light weight. As a plus all our new shaft designs allow for the use of a thrust bearing on the outside of the diff instead of a normal bearing to handle side load much better. This leads to a smoother, longer lasting diff.
The Reflex Racing Mass Damper Set is designed to smooth out your 1/28 scale car by reducing the amplitude of vibration on the front end caused by the uneven nature of RCP Tracks. The mass damper is mounted on the ballast weight hole on any Reflex Racing Carbon Bumper or on the body clip posts of your RX512 Jomurema bumper. The result is a car that is smoother to drive and more controllable at high speed and through bumpy sections. Adjust the Damper by using a different combination of weights.
The set includes:
3x 0.9g Tungsten Weights1x 4mm aluminum post2x M2x3 CS Screws.
These sleek-looking steel bumper weight set allow you to fine tune your weight bias on your Mini-Z when used in combination with any of our Carbon Fiber Bumpers. When running on bumpy or high grip environments, playing around with a little bit of nose weight can impact tremendously the behavior of your car. This weight set allows you to fine tune your nose weight in 1g increments. This is easily achieved by stacking the thru-hole weights and then clamping them down on the bumper with the threaded weight on top.
Included in the set is:
2x 1g thru weights
1x 1g threaded weight
1x M2x4CS Screw
1x M2x6CS Screw
The Reflex Racing Mass Damper Set is designed to smooth out your 1/28 scale car by reducing the amplitude of vibration on the front end caused by the uneven nature of RCP Tracks. The mass damper is mounted on the ballast weight hole on any Reflex Racing Carbon Bumper or on the body clip posts of your RX512 Jomurema bumper. The result is a car that is smoother to drive and more controllable at high speed and through bumpy sections. Adjust the Damper by using a different combination of weights and springs.
The set includes:
2x 0.9g Tungsten Weights1x 8mm aluminum post-2x M2x3 CS Screws. (use M2x3 CS Screw on top of the mass damper top spring when installing 1 weight).1x M2x6 BH Screw (use M2x6 BH Screw plus M2 gold washer on top of top spring when installing 2 weights).1x M2 Gold Washer2x Black MD Spring (Soft)-2x Silver MD Spring (Medium)
Made with flexible Silicone Sheathing, this ESC to receive link wire is more easily coiled, routed and shorter than std wires usually supplied with electronics. Up your wiring game and use this all black wire for the stealth look! This set comes with 1 wire. ESC Side plug is not installed. You must match the wire order to the oem wire supplied with your electronics.
Made with flexible Silicone Sheathing, this ESC to receive link wire is more easily coiled, routed and shorter than std wires usually supplied with electronics. Up your wiring game and use this all black wire for the stealth look! This set comes with 5 wires. ESC Side plug is not installed. You must match the wire order to the oem wire supplied with your electronics.
2x Kugellager für das Hauptzahnrad.Passend für Reflex Racing, PN Racing, Nexx Racing Hauptzahnräder.Dimensionen: Innendruchmesser 4mmAussendurchmesser 7mmBreite 2mm
What makes the Reflex Ball Diff Special? Attention to details. We worked on sourcing the highest quality materials and ended up with a light weight ball diff that has better engagement and acceleration.
The ball diff comes standard with super hard steel diff rings, 7075 T6 aluminum diff shaft, carbide diff balls, hard o-ring for tighter adjustment, our specially designed 10 ball spur gear and lightweight 7075 aluminum shaft and diff parts. The V4 diff now also comes with a molded spur and spur gear covers. The spur gear is super durable, quieter and much longer lasting. The covers are now about 50% lighter than the aluminum variants, which gets the weight down to a scant 6.6g with covers and 5.8g without (including the left hub).
Montage Anleitung V2/V3/V4 Diff.
Das Reflex V3 Werkzeugset - jetzt mit einem neuen Griff Design und zusätzlich mit einem Philips 00 Kreuzschraubenzieher, welcher sich bestens für die kleinen Pivot Schrauben des RX28 eignet. Das V3 Werkzeugset kommt wieder in einem praktischen Etui, welches die Werkzeuge schützt und Ordnung hält. Es beinhaltet alle notwendigen Werkzeugschlüssel, um deinen RX28, GL Racing, RTA oder MWX zu montieren. Das Werkzeugset enthält: Inbus-Schrauber:0,9mm1,3mm1,5 mmBox-Schlüssel:4.0mm4,5 mm Phillips-Schrauberzieher:#0#00
It's finally here! Our all new Gear differential was designed to be a high quality and high performance addition to your 1/28 scale car. More rotation and harder acceleration than the ball differential yields a car that is often about a tenth faster to drive in high traction surfaces. The feel of this gear diff is very balanced and this makes the acceleration super smooth and strong. At only about 4.7g, it is also super light for less rotational mass.
The gear diff is sealed from the elements as the gears are inside a machined aluminum case in which you can larger amounts of grease to change the behavior of the differential action. The ticker the grease, the lower response into the corner, but this could be at the expense of a little bit of exit traction. We don't recommend going too heavy on the oil (maybe use no more than 1 or 2k CST oil), but you can use oil with no leakage at the spur and only slight leaking at the outputs.
MANUAL
**Please not the diff is not sealed at the bearings, so it is not designed to be "filled" with oil , but a healthy amount can be used when building. Left hub is not included.
This charging cable was designed to be used with XT60 output chargers to be used with our hard case battery packs. Durable, stylish and perfect length cables to help you tidy up your pit space!
This charging cable was designed to be used with XT60 output chargers to be used with our hard case battery packs. Durable, stylish and perfect length cables to help you tidy up your pit space!
This is a set of Full Ceramic Bearings for you 1/28 scale Pan Car. Full Ceramic Bearings offer many benefits as outlined below:
Reduced Friction: They provide lower rolling resistance, which can improve the car's speed and overall efficiency.
Enhanced Durability: The wear-resistant nature of ceramic bearings means they can last longer under the high stress.
Lightweight: While not a lot, a full set of ceramics drops about 0.5g off your car.
Reduced Maintenance (somewhat): The low friction and wear properties eliminate the need for oil or grease. However, as our bearings have no races, they can allow more debris and tire dust to enter the bearings.
Corrosion Resistance:As they are not metallic, your bearings can be washed with something like dish soap and water.
https://www.youtube.com/watch?v=7tmryrOY6PA
Replacement front end for your RX28 or RX28K Upgrade
It includes:
BulkheadUpper and Lower Hinge PinsGray (Hard Arms)RX28 Shock Set with Green Front SpringsFront Shock TowerNecessary Hardware For Installation of all parts on the front end.
Required:
KnucklesFront Axles
All New RX28 Steel Chassis for your RX28G2 Plate Cars. This new chassis allow for fore and aft movement of 20mm wide batteries as well as making it compatible with our new 400mah batteries that are 24mm wide. This new chassis kit comes with lateral CF braces to locate the battery side to side, but also to stiffen the front to back structure of the car for more precise handling and higher corner speeds. The kit is finished off with a new forward center shock mount that incorporates a band-less battery hold down that is more reliable and easier to use.
This short steering horn is designed for high traction applications where your car is too edgy and you are looking for a slower steering feel. It is ideal for Pan Car and larger flowing tracks where you do not need as much steering throw. Due to the design of the shorter horn, you will only be able to achieve about 80% of the previous steering throw, so if you are using 85%+ Dual Rate, this is probably not the horn you want to use.
The affectionately called "Schuur Horn" provides a more linear steering geometry for your RX28. By moving the pivots of the steering horn to the front, we achieve a higher angle on the links which created less ackerman effect on your front tires. The result is a steering feel that is much less exponential as dual rate is increased. This can allow you to run less steering throw in high traction conditions, or set up more aggressively for tight tracks with 180s where more throw is needed.
Shed some weight from up top for an even lighter CG. This shaft sheds 0.3g from your top shock, leaving behind a 1.41g top shock. When combined with the new aluminum turnbuckles, part no: RX28A-44, it will shed 0.85g up top.
Shed some weight from up top and look good while doing it with these. Both Turnbuckles together save approximately 0.5g from one of the highest points of the car. When combined with the New Aluminum Top Shock Shock Shaft it sheds about 0.85g.
The V2 have a new hard-coating for longer lasting wear characteristics. High quality 64 Pitch 7075 T6 Aluminum pinion gears for your 1/28 scale car. Each gear set comes with: 1 x 10T pinion
1 x 11T pinion
1 x 12T pinion
1 x 13T pinion
1 x 14T pinion
1 x 15T pinion
All new from Reflex Racing is our Aluminum Tweak Station. Precision machined from 7075 aluminum and high grade stainless steel, this tweak station is precise, light weight and easy to use.
The tweak station features 3 adjustable feet as well as a bubble level to set the station level in North-South and East-West. The Station pivoting bar is also ball raced for minimum friction and maximum precision.
This station is compatible with any wheelbase from 98mm all the way to 116mm so most of you 1/28 scale cars should be able to be adjusted with this awesome tool
Set of 3 tire gauges to make your tire measuring experience much easier.
To Use:
Select the appropriate gauge by measuring against the tire.Once selected, push the open side of the gauge onto the tire. Once you feel slight resistance and the center of the wheel is aligned with the resistance point, this is the measurement for your tire diameter.
All new from Reflex Racing is the MC1 30A ESC. This ESC is not just a re-labeled unit, but rather a proprietary ESC and Software designed from the ground up specifically for 1/28 scale (and other Micro scales) for racing. Curated to use the highest quality components and craftsmanship, the result is an Ultra-High Performance, super adjustable and durable ESC. The ESC is adjustable via the RRE024 MC1 Programming Box and has been designed to be used with a soon to be released bluetooth dongle and App. *All ESCs come with a 90 day limited warranty which covers manufacturing defects or DOA units. Reverse polarity connection is not covered under warranty.**Please note that the price reflects the current additional tariff rate.
Anleitung:
MC1 Manual
The RX28D Gen 3 is here to redefine what a 1/28th-scale RC car can do. Designed for drivers who demand speed, agility, and pinpoint control, this third-generation model packs a host of upgrades that make every run feel like a victory lap.
The revamped front end features 1mm longer arms for improved stability, paired with a sway bar system that lets you carve corners with surgical precision. Fine-tune your setup with adjustable caster (3 screws), an integrated shock tower with shim adjustment, and adjustable upper arm hinge pin height for tailored camber gain and roll center. The RX28D also comes with all new lighter, but durable plastic knuckles and they are combined with also new, low-profile big bore shocks and springs which ensure smooth, responsive handling, giving you the edge on any surface.
The rear end sees many improvements as well. A new, much lower CG Rear End sees an all new motor mount that lowers the motor by 0.8mm, a new damper mount secured by 3 screws for easier service to the rear suspension, a tweak brace dropped 1.25mm, shorter side springs, thinner spring perches, side dampers lowered by 3mm (secured by screws on the motor mount), and smaller diameter center shock spring, collar and perch, all which allow for higher corner speeds and quicker direction changes. Finally, a pinned Rear Motor Pod Plate increases precision and durability on the car.
This third generation car is also much easier to work on as well. The car now uses mostly ball studs all around, which standardized hardware and makes it much easier to work with.
The RX28D Gen 3 comes ready to roll with one set of wheels and tires, perfect for getting you on the track fast.
Dimensions:
98mm Wheelbase
145g-170g weight RTR Depending on body and Electronics
69mm to 78mm Rear Track Width
72mm to 75mm Front Track Width
Need to Complete:
Body and mounting hardware
Electronics: Motor, Lipo Battery, ESC, Receiver and Servo (Please note, the provided servo horn is designed to work with the AGF A06CLS Servo 20T Spline. Additionally, the GL Titanium Servo will fit as well.
****ELECTRONICS ARE NOT INCLUDED!!!
